Wednesday, November 30, 2011

Sweet Pea (In the beginning)

Gary has worked so hard to restore our little Shasta travel trailer. We named her "Sweet Pea" so I thought it would be good to remember where we started because this process has taken a year at this point.

Back to the inside to put in insulation and start replacing veneer,and new wiring

Augustl 1, 2010
I reworked wiring and added some extra circuits in the trailer,so we would have the outlets we needed and also be able to handle the amps. we would need. You can also see that the wooden studs in the walls and over head wood is only 1by2 inch pine. The ceiling was sagging down some, so I bought some 3/4 inch aluminum angle and screwed them in on each side. That would help a lot when I went back with the new Birch veneer.
 
The insulating of the  trailer went pretty fast, I bought 4 by 8 foot sheets of insulation and cut it to fit. The insulation was 3/4 inch same thickness as the pine wood. I would mark the width I needed with A black pen then cut it with a razor blade knife , I also had a Roto-Zip tool that came in handy.










You can see the copper tubing and wire in the side of the wall. That is when I got my note book back out and made a drawing of every stud and brace in each side,top, back, and front of trailer. When you begin to put veneer back in you have to know where those wires are so you want run a nail or screw in them.
I've been working hard replacing the insulation and veneer. The blue masking tape is marking studs where wires are going though the wall. Buying prefinished veneer saved me a lot of time and work. If you use prefinished veneer do not leave the tape on any longer then necessary.






It's beginning to take shape again and look like a trailer on the inside although still along ways to go. You are looking at the overhead cabinets in the front of the trailer.




The shelf in the bottom picture will go in the back of the trailer. I had to remake it with new veneer. I used the old shelf as a pattern and also reworked front shelf. Getting the veneer back in the trailer really stiffened the trailer back up.

Tuesday, November 29, 2011

Painting is Completed!! WooHoo!

July 8,  2010
 Finally the painting was completed and this is the finished product after all the tape and paper has been removed. I painted the trailer hitch and bumper white to match the trailer.
When you are preparing your trailer for painting take your time when removing dings and dents in the siding. I thought I had done a pretty good job, but when I begin to spray that finish coat on I didn't have any problem seeing the area's that I should have given a little more tender loving care. I am still pleased with how it turned out. This one and one more will be two for me! HA HA
I had already rebuilt  the door frame and prepared it for painting. So I just had to make sure I matched up the stripe on the door with the one on the trailer.









This has been a long process, sanding, priming and removing dents and dings. It is very important to
wear a good respirator during this process for your protection.
After having painted the trailer I removed the wheels and had them
powder coated to match the red stripe. I will next order baby moon hubcaps.

Monday, November 28, 2011

Paint Booth, Priming and Taping

June 3, 2010

This was our make shift paint booth. We hung plastic from the rafters to the floor on three sides of the trailer. We wanted to keep as much dust as possible out of the painting area. I also did not want to get paint on  everything else in the shop. We also put an exhaust fan in the front door to help pull the paint fumes out.



I put 2 inch masking tape around the trailer where the stripe was located. I then sprayed etching primer on all the bare metal, so that when I came back and primed the entire trailer it would all bond to the aluminum siding.



The top half has been primed and painted white then covered with paper again so the bottom of the trailer can be painted it's finish color of blue-green.










The trailer has been covered with paper and the stripe has been masked off so that the red stripe can be painted down the side of the trailer.  This was quite a learning process.
 

Sunday, November 27, 2011

Getting trailer ready for new paint job. sanding, dent removal,

May 17, 2010
Once I had the trailer back on the floor with the frame and new wood under it, I decided to move to the outside of the trailer and begin preparing it for new paint job .  All of the windows had already been removed . They would later be polished, repaired if need be then reinstalled with stainless steel screws.
   

 This part of the project was really going to be a learning experience for me. I have done a lot of wood finishing projects and could use a spray gun, but had never worked much with metal or sprayed painted anything this large.
There were lots of dings that this little lady had to show for almost 50 years of being around. They had to be sanded and filled and then sanded again. I knew that time spent in preparing the skin of the trailer for painting would be well worth the effort. So I took my time and tried to patiently work my way around the trailer several times making sure that no part of the trailer was left untouched.

I do know why the colors on the trailer look so different in the photos. The original color was blue and white. The door was removed and all the windows and openings covered with plastic sheeting. A lot of the sanding I did with a Pam sander but used a lot of single sheets also. Some places on the trailer was down to bare medal where it wasn't I wanted to feather the edges so they were smooth, so when I painted the trailer it would look and feel like new.

Friday, November 25, 2011

Putting the floor under the trailer

April 4, 2010

I purchased new 3/4 inch plywood and new black fiber board to go under the plywood. I used carriage bolts to pull it all down. I pulled the bolts down far enough that the flooring could be puttied over and then smoothed. This was in preperation  for the Armstrong vinyl checkerboard flooring that would be glued down.




You can see that all the 2X4's were replaced, that was under the floor also.









Next I took the framing down that had supported the trailer while the floor and frame was being worked on. I was happy to see that go, I can't tell you how many times I would raise up and hit my head on it. Ha Ha  That was the frame of many names!
The the floor has now been put back in place and the trailer lowered to the floor and reattached. . Next,  I am going to move to the outside of the trailer and prepare it for painting while the weather is warm.














Thursday, November 24, 2011

Removing frame from under trailer, and replacing bad wood


January 11, 2010

We built a frame to hold the trailer up so the trailer metal frame bed could be detached and lowered and pulled from under the trailer top. Once that was completed, I begin to replace damaged studs and wood around bottom of trailer. When frame  was sandblasted and painted a new floor was put down.  I wanted good treated wood for it to fasten into.



 Due to a snowfall and the shop not being heated except for space hearters, work on the Shasta stopped until spring, when I was able to get back into the shop and work again on replacing the bad wood.





This wood was replaced at the rear of the trailer surrounding the compartment door and, reworked both sides.
  This is in the front of the trailer.  You can see I replaced the vertical stud, also wood along bottom side with treated pine, and replaced wood along front of the trailer. The vertical stud was fastened and held in place with a 90 degree angle with screws.